Pool heating and dehumidification Dehumidifiers for indoor pools DANTHERM CDP 70 built-in dehumidifier DANTHERM CDP 70 built-in dehumidifier
Recommended retail price 2024 starting from :
7300 €
Our Price starting from :
7300 € Including VAT
Ref. Abatik 023551
Ref. Provider CDP 70T
DANTHERM CDP 70 T standard built-in dehumidifier
Ref. Provider CDP 70T
DANTHERM CDP 70 T standard built-in dehumidifier
Built-in dehumidifier perfect for indoor pools with a maximum surface area of 40 m²
Capacity 4,2 l/h
Incorporated hygrostat,
Available with integrated heater,
Remote control on option
Capacity 4,2 l/h
Incorporated hygrostat,
Available with integrated heater,
Remote control on option
In stock
DANTHERM CDP 70 T standard built-in dehumidifier
Ref. Abatik 023551 Ref. Provider CDP 70T
Ref. Abatik 023551 Ref. Provider CDP 70T
7300 €
DANTHERM CDP 70 T built-in dehumidifier with hot water battery
Ref. Abatik 023557 Ref. Provider CDP 70T+094335
Ref. Abatik 023557 Ref. Provider CDP 70T+094335
7690 €
DANTHERM CDP 70 T built-in dehumidifier with electric heater
Ref. Abatik 023554 Ref. Provider CDP 70T+094338
Ref. Abatik 023554 Ref. Provider CDP 70T+094338
7690 €
Wall crossing kit + aluminium grills for DANTHERM CDP 70 T built-in dehumidifier
Ref. Abatik 023560 Ref. Provider 093508
Ref. Abatik 023560 Ref. Provider 093508
1090 €
DRC 1 remote control for DANTHERM CDP
Ref. Abatik 023547 Ref. Provider 093455
Ref. Abatik 023547 Ref. Provider 093455
335 €
The CDP dehumidifiers have been specifically developed for spas, hammams, verandas, libraries, museums and sports facilities. In brief, this unit is suitable for any environment which requires precise humidity control.
The CDP has been specifically developed for spas, hammams, verandas, libraries, museums and sports facilities. In brief, this unit is suitable for any environment which requires precise humidity control.
Humidity present in the ambient air is suctioned by the ventilator which is integrated into the dehumidifier. Air which passes through the evaporator is cooled to below condensation point, water vapour is then condensed and evacuated. Dry air passes on the condenser, is heated and then is sent into the ambient atmosphere.
Following dehumidification treatment, ambient air temperature gains approximately 5°C.
The dehumidifier is entirely automatic. Very quiet to run and controlled by an integrated hygrostat. A digital control panel clearly shows operational modes. Easy to maintain, just lift off the front panel to clean the air filter.
The CDP has been specifically developed for spas, hammams, verandas, libraries, museums and sports facilities. In brief, this unit is suitable for any environment which requires precise humidity control.
Humidity present in the ambient air is suctioned by the ventilator which is integrated into the dehumidifier. Air which passes through the evaporator is cooled to below condensation point, water vapour is then condensed and evacuated. Dry air passes on the condenser, is heated and then is sent into the ambient atmosphere.
Following dehumidification treatment, ambient air temperature gains approximately 5°C.
The dehumidifier is entirely automatic. Very quiet to run and controlled by an integrated hygrostat. A digital control panel clearly shows operational modes. Easy to maintain, just lift off the front panel to clean the air filter.
Operation
Remote control
(option)The CDP can be equipped with a wireless remote that indicates the humidity rate and temperature of the room.
The DRC1 distance control unit features an "installation mode" that can regulate heating system temperature and evacuating ventilation. It is also possible to connect the distance control unit to the CDP dehumidifier printed circuit board.
If the model you have chosen has featured heating, the ventilator automatically starts when the heater starts.
The distance control can be "locked" to avoid any unwanted modification to your settings.
The DRC1 distance control unit features an "installation mode" that can regulate heating system temperature and evacuating ventilation. It is also possible to connect the distance control unit to the CDP dehumidifier printed circuit board.
If the model you have chosen has featured heating, the ventilator automatically starts when the heater starts.
The distance control can be "locked" to avoid any unwanted modification to your settings.
The Dantherm CDP 70 built-in unit is installed next to the room that requires dehumidification. Ambient ventilation is fed through using a wall crossing that operates using a ventilation suction and a ventilation discharge grill. The heater that can be incorporated optionally by choosing the hot water battery or heater models. This can control the humidity rate of indoor pools by dehumidifying on a closed circuit.
A passive defrosting system is integrated into the electronic control. A sensor situated on the unit's evaporator ensures defrosting only when required. When in defrost mode, the compressor stops and the ventilator sends ambient air onto the evaporator, which is, in turn, defrosted.
The CDP 70 operates automatically by electronic control and incorporated hygrostat. The hygrostat is factory set to a relative humidity rate of approximately 60%.
The digital control panel indicates various unit status:
1. The unit is connected to its power source
2. Dehumidification - the compressor is in operation
3. Cooling circuit error - the dehumidifier is not in operation
4. The heating battery is connected (for models which feature hot water battery)
1. The unit is connected to its power source
2. Dehumidification - the compressor is in operation
3. Cooling circuit error - the dehumidifier is not in operation
4. The heating battery is connected (for models which feature hot water battery)
Characteristics
Model
CDP 70 built-in
Air flow
900m3/h
Power supply
230 V (Ph+N)
Electrical capacity
1,8 W
Amperage
8 A
Dehumidification at 30°C - 80% H.R.
103 L/day
Dehumidification at 28°C - 60% H.R.
69 L/day
Dehumidification at 20°C - 60% H.R.
40 L/day
Decibels at 1m
47 dBa
Cooling liquid
R407C
Quantity of gas
1,2 kg
Compressor
Rotary
Index of protection
IPX4
(1) Hot water battery option (kW)
6,2
Electric heater option(kW)
5
(1) Information based on primary circuit water temperature at 80/60°. Ambient air 28°, relative humidity rate 60%.
Ambient temperature
Ambient temperature
10 - 36 °C
Ambient humidity rate
40 - 100 % H.R.
Dimensions and weight
Depth x height x width
304 x 700 x 1483 mm
Weight
77,5 Kgs
Dimensions of grills and wall crossing
| Dimensions | A | B | C |
| / (mm) | 950 | 1483 | 1126 |
Advantages
High-quality product
Bodywork made from galvanised steel, painted on inner and outer surfaces.
Discreet installation
Aluminium ducts and grills for enhanced, discreet installation.
Low energy consumption
Rotary compressor and radial ventilator.
Very quiet in operation
47 decibels measured at 1 meter from the dehumidifier.
Examples of installation
Warranty
2 years
Photos non-contractual
Price incl. VAT
Price incl. VAT
Ask for a free quote dantherm cdp 70 built-in dehumidifier
Other product : DANTHERM CDP 70 built-in dehumidifier
Starting from 7300 eur Including VAT.
Please fill in this form carefully. Our commercial service will handle your request promptly.
UK freephone hotline
Monday Friday 9.00 18.00
Spare parts order
You are looking for a spare part for «DANTHERM CDP 70 built-in dehumidifier» ?
Please click the button below. Our commercial service will handle your request promptly.
